Two boxes comparing the two clocks at 600 feet and 65 mph: 6.3 seconds in view and 4.1 seconds to read 7 words.

OOH Education / Billboard design

How Long Does a Driver Have to Read a Billboard?

Most answers say “about six seconds.” That is the time a board is in view, not the time a driver spends reading it. Here is how to work out both clocks for your own board, and why the second one is the one that decides how many words you can use.

By Dan Resnikoff, Principal Billboard Strategist, Ad Corrector®
Published: · Updated:

Disclosure: I created Ad Corrector. The time-in-view numbers are my own arithmetic (distance divided by speed). The reading-time research was done on road guide signs, not advertising billboards, so treat every figure as a planning starting point.

Short answer: at highway speed, a board is in view for roughly 5 to 6 seconds over the last 500 to 600 feet. A driver does not spend that time reading. Drivers look in short glances between looks at the road, so the message has to work in pieces. Plan on a message that takes about 4 seconds or less to read, which is roughly 7 words or fewer, and make sure the letters are large enough that the clock starts early.

Clock one: time in view

Time in view is how long a board is available to the driver while the car covers a given distance. The formula is distance ÷ speed. Speed in miles per hour times 1.47 gives feet per second, so 65 mph is about 95 feet per second.

Seconds in view, by speed and distance from the board
SpeedFeet per secondFrom 300 ftFrom 500 ftFrom 600 ftFrom 800 ft
25 mph36.78.2 s13.6 s16.4 s21.8 s
35 mph51.35.8 s9.7 s11.7 s15.6 s
45 mph66.04.5 s7.6 s9.1 s12.1 s
55 mph80.73.7 s6.2 s7.4 s9.9 s
65 mph95.33.1 s5.2 s6.3 s8.4 s
70 mph102.72.9 s4.9 s5.8 s7.8 s

Two things stand out. Slower roads buy a lot of time: a board seen from 600 feet at 35 mph is in view for nearly twice as long as the same board at 65 mph. And the distance you start from matters as much as the speed, which is why the next two sections matter.

Clock two: reading time

Reading time is how long the message takes to process. Road-sign researchers have modeled it as a function of the number of familiar words, and the estimates differ:

  • One-third of a second per word. An early relationship by Mitchell and Forbes, described in an FHWA report, for signs with more than three words.
  • Half a second per word. The Ontario Ministry of Transportation method, summarized in a National Academies human factors tutorial, for the critical words on a sign.
  • 0.31 seconds per familiar word plus 1.94 seconds. Ad Corrector’s own reference estimate, calculated by the tool. It is not taken from a published study and has not been field validated. The fixed 1.94 seconds is an allowance for taking in the message as a whole.
Estimated reading time in seconds, by word count
Words1/3 s per word1/2 s per wordAd Corrector reference
31.0 s1.5 s2.9 s
51.7 s2.5 s3.5 s
72.3 s3.5 s4.1 s
103.3 s5.0 s5.0 s
124.0 s6.0 s5.7 s

Ad Corrector’s reference is the most cautious for short messages, because it carries the fixed 1.94 seconds. Whichever estimate you prefer, the shape is the same: each added word costs a third to a half second, and the cost comes out of a window that is already short. At 600 feet and 65 mph, 7 words leave about two seconds to spare under the Ad Corrector reference. Twelve words leave less than a second, before anything else goes wrong.

Why the real window is shorter

The clock starts where the letters become readable

A board is not readable from the moment it appears. It becomes readable at the distance its letters allow. With the legibility figure of about 1 inch of letter height per 30 feet, 12-inch letters can be read from about 360 feet and 24-inch letters from about 720 feet. At 65 mph, 360 feet is about 3.8 seconds, which is less than the 4.1 seconds the Ad Corrector reference gives for 7 words. The same message in 24-inch letters starts the clock at about 7.6 seconds. Letter size is how you buy time. See what letter height a billboard needs.

Drivers look in short glances

The time in view is not time spent looking. An earlier study (Beijer et al., 2004) reported an average billboard glance of 0.57 seconds. In FHWA’s 2013 eye-glance study, the longest glance at a standard billboard was 1.28 seconds, according to a summary published by the Outdoor Advertising Association of America. Some reviewers questioned that study’s glance data, so read the figure as one data point.

The practical lesson is that a message is taken in over several short looks. A board that makes sense one fragment at a time, with the main idea first, survives that. A board that needs to be read from start to finish does not.

The last stretch is unreadable

Near the board, the viewing angle gets extreme. Road-sign guidance adds half a second to reading time for exactly this reason, in the same tutorial. For a board beside the road, the closest part of the approach contributes little.

Why sources give different times

Search for how long a driver has to read a billboard and you will find two seconds, under five, six to eight, and more. Most of these figures are not wrong. They measure different clocks, and they are rarely labeled. Match each figure to what it measures before you use it.

Common figures, and what each one actually measures
Figure you will seeWhat it usually measuresWhat the evidence shows
About 2 secondsHow quickly the message has to register in a lookMeasured glances are shorter: 0.57 seconds on average in one study, and 1.28 seconds for the longest glance at a standard billboard in FHWA’s 2013 study (see above)
Under 5 secondsTime in view from a shorter distance or at a higher speedFrom 500 feet, 4.9 seconds at 70 mph and 5.2 seconds at 65 mph (table above)
6 to 8 secondsTime in view from a longer distance at highway speed6.3 seconds from 600 feet and 8.4 seconds from 800 feet at 65 mph (table above)
8 secondsOften the digital billboard dwell time: how long one ad stays on screenA 2007 FHWA memo recommended about 8 seconds per digital display, within a 4- to 10-second range. That is screen time, not driver time
⅓ to ½ second per wordReading time per wordRoad guide sign research (see Clock two above)

The practical rule: when you see a time figure, ask which clock it describes, at what speed, and from what distance. A number with none of those attached cannot be checked. Ad Corrector’s Reading Time Reference shows the two clocks that matter for your board, time in view and reading time, side by side.

Working it out for your board

  1. Pick the speed. Use the posted speed or the speed traffic actually travels where the board sits.
  2. Find the first readable distance. Multiply your capital letter height in inches by 30 to get feet. A 20-inch letter gives about 600 feet.
  3. Divide distance by speed. That is the time in view. At 600 feet and 65 mph, about 6.3 seconds.
  4. Subtract a margin. Held-back glances, other traffic, and the unreadable last stretch all eat into it. Keeping at least a couple of seconds spare is a reasonable cushion.
  5. Spend what remains on words. At about a third to a half second per word, plus a second or two to find and take in the board, the remainder tells you how many words fit. For most highway boards that lands at 7 words or fewer.

If the answer comes out too tight, there are two fixes: fewer words or bigger letters. Adding time by moving the board is rarely an option.

How Ad Corrector shows it

Ad Corrector’s Reading Time Reference puts both clocks on the results page. It estimates reading time from the confirmed copy, using 0.31 seconds per familiar word plus 1.94 seconds, and compares it with the time in view for the speed and distance you selected. If the smallest measured line is readable only from closer than the viewing distance, time in view starts from that closer distance. It is a reference only and does not change the grade.

The Scenario Simulator re-runs the same artwork at a different speed or distance, so you can see how the margin changes. Speed View shows an illustrative blur for the settings you choose. It is a visual aid and not a recording of a driver’s view.

Where this guidance stops

The reading-time estimates come from research on road guide signs, where drivers are looking for specific information. A billboard is a different job, so these figures describe how much text is plausible to take in, not how much a driver will actually read. Time in view assumes a straight, clear approach at a steady speed. Curves, traffic, and obstructions shorten it.

None of this measures whether a message is remembered or acted on. For the gap between seeing and understanding, read Why Billboard Visibility Doesn’t Equal Understanding. Confirm final specifications with your media owner and a full-scale proof.

Reader questions about billboard reading time

How long does a driver have to read a billboard?

At highway speed, a board is in view for roughly 5 to 6 seconds over the last 500 to 600 feet: about 6.3 seconds from 600 feet at 65 mph. Drivers look in short glances, so the usable reading time is shorter than the time in view.

How do you calculate time in view for a billboard?

Divide the distance by the speed in feet per second. Multiply miles per hour by 1.47 to get feet per second. At 600 feet and 65 mph (about 95 feet per second), time in view is about 6.3 seconds.

How long does it take to read a billboard?

It depends on the word count. Ad Corrector’s reference of 0.31 seconds per familiar word plus 1.94 seconds gives about 4.1 seconds for 7 words and 5.7 seconds for 12. Older road-sign research suggests one-third to one-half second per word.

How many words can a driver read on a billboard?

A working limit is 7 words or fewer for the main message. At 600 feet and 65 mph that leaves about two seconds to spare under Ad Corrector’s reading-time reference.

Why do sources give different times for reading a billboard?

Because they measure different things. Figures near 2 seconds usually describe how fast a message must register in a glance. Figures of 5 to 8 seconds usually describe time in view, which depends on speed and distance. An 8-second figure is often the dwell time a digital billboard shows one ad, which is screen time, not driver time.

Do drivers read the whole billboard?

Usually in pieces. Studies of driver glances report short looks, with an average billboard glance of about 0.57 seconds in one study. A message that works one fragment at a time, with the main idea first, holds up best.

Is there more time to read a billboard in the city than on the highway?

Yes. At 35 mph, time in view from 600 feet is about 11.7 seconds, nearly twice the 6.3 seconds at 65 mph. Slower roads allow somewhat more text, though a short message is still the safer choice.

Does Ad Corrector calculate reading time?

Yes, as a reference. The Reading Time Reference estimates reading time from your confirmed copy and compares it with time in view for the speed and distance you select. It does not change the grade.

Sources and notes

Research and standards: FHWA report on reading time for guide signs (Mitchell and Forbes relationship); Human Factors Guidelines for Road Systems, Tutorial 5 (National Academies); Beijer et al., 2004 (VTI); FHWA CEVMS report summary (OAAA); FHWA guidance on off-premise changeable message signs, September 25, 2007 (archived); Caltrans, Digital Display Safety preliminary investigation (summarizes the 2007 memo’s 8-second duration).

Calculations: time in view is Ad Corrector’s arithmetic, distance divided by speed, with 1 mph taken as 1.467 feet per second. Reading times for 7 words and other counts use the stated per-word figures. Letter-height distances use 30 feet per inch.

Ad Corrector references: Scientific Foundations and methodology.